Single to 3 phase convertors provide three phase power from a single phase supply. Ampair achieves the 3 phase power conversion using an internal motor-generator with 600% overload capability and no electromechanical contacts.
For three phase convertors: E-mail by clicking including delivery location so we can use an appropriate currency and estimate transport costs, power required in kW or HP and state if you need to derive single phase from one of the 3 phases and neutral, e.g. for an electronic controller on a CNC machine.
For price list with dimensions and ratings or to purchase on-line, click on Boost-Energy.
Phase convertors are ideal for farms, workshops, garages, large buildings, etc. Ampair primarily supplies the UK (Great Britain and Northern Ireland), the Republic of Ireland, Spain, Canary Islands, Ballearic Islands, Hungary, Turkey, Iran and other countries in Europe, Africa and the Middle East. See Business partners for UK, Australia, Canada, USA, Mexico, New Zealand and Pacific Rim. See also 3 phase conversion understanding and selection.
The Booster™ range is shown in the photograph below. The smallest example covers Boosters™ from 1.5 to 3 kW. The larger enclosure with internal motor covers Boosters™ from 4kW to 8kW. The example with external motor covers Boosters™ of 12kW and 16kW rating.
Booster™ A three phase convertors will supply a number and variety of loads at full performance. Unlike 'static' phase convertors, they are not limited to driving a single motor, nor do they limit the motor's torque or have a lower limit to output power. The Booster™ range of 3 phase convertors has the unique feature of electronically switching up to 600 % of rated power for up to 10 seconds for 'hard starting' or momentary overload. Solid state switching takes place as the power waveform crosses zero, minimising electromagnetic interference. There are no electromechanical contacts to wear out or open at full voltage (emitting interference). The Booster™ D range has improved voltage balance between phases and incorporates power factor correction. For an explanation of the principles of 3 phase supplies and a guide to 3 phase convertor selection, go to the 3 phase convertor understanding and selection page
Many properties are, for economic reasons, only connected to one of the three phases of utility power available at the nearest distribution transformer. A single phase supply line was the cheaper option when the premises were built. Similarly, large buildings with 3 phase supplied might still have locations where it is uneconomic or inconvenient to run 3 phase wiring.
If three-phase equipment is to be used, a simple comparison can be made: compare the cost for providing three-phase supply (e.g. distribution transformer, power lines, monthly line charges) with the price of a single to three-phase convertor.
Lathe, Drill, Milling machine, Grinder, Saw, Polisher, Shaper, Guillotines, Press, Welder.
Post lift, Hoist, Welder, Wheel balancer.
Pumps, Compressors, Irrigation systems, Air conditioning, Refrigeration unit, Conveyor, Crane, Hoist, Wine press, Olive oil processor, Grain mill.
Computer installations, print rooms, etc.
Booster™ A 3 phase convertors are suitable for all the applications listed above. They can run one or many motors. They can be compared with other single to three-phase convertors available worldwide, except they electronically switch 600 % rated power for up to 10 seconds and need no maintenance because they have no electromechanical contacts.
Rotary phase convertors are capable of starting many motors simultaneously, even under load. With a Booster™ A, motors will reach full speed in the shortest possible time. Motors also maintain their speed when momentarily overloaded.
This unique convertor copes well with the most difficult applications: Metal lathes without clutches, hydraulic systems, refrigeration units, wheel balancers, older types of compressors. A Booster™ A will cope with start-stop operation, with forward-reverse and with electric brakes.
The Booster™ A can be used with Variable Speed Drives.
Install a single-phase industrial wall switch-socket combination. Connect your new convertor. Now you have three-phase power for all your electric motor and machine tool requirements.
Motor speeds are constant as with a three-phase supply. Starting motors draw high currents. A Booster™ A will produce these currents in order to maintain output voltages. This will draw high input currents for a short time. On the single phase supply side it pays to install heavy cables. This will minimise voltage drop.
Installation instructions and service schematics are provided with each convertor. A simple block diagram is shown below.
When an electric motor starts under load, or when a heavy load is applied to a motor, a Booster™ will output up to 600% of its continuous maximum current for up to 10 seconds.
Booster™ A convertors cope well with motors starting under load, with motors accelerating large inertia and with pumps and compressors starting against pressure.
A Booster™ A will operate chillers, cranes, conveyors, hoists and vehicle lifts/ramps starting under load. Due to the higher input currents during Boost mode, single phase supply cables to a Booster™ should be oversized. The resistance per unit length of the cable should be multiplied by the length and by the maximum current to provide the voltage drop. As a rough guide, this should not exceed 10V at peak current.
Efficiency is highest (max. 90%) at a load between 20% and 90% of the rated power. Above and below this range, efficiency is slightly lower. Running idle, a Booster™ will consume about 5% of its rated power.
Boosters™ are totally maintenance-free. Internal motor-generators are brushless and bearings are greased for life.
Boosters™ do not have any life-limiting components such as contacts, contactors or electrolytic capacitors. Internal logic is CMOS, which stays cool even under heavy loads.
Boosters™ are robust and immune from incoming line disturbances, over- or undervoltage conditions and short circuits.
The life of a unit is at least 10000 hours before any component needs to be replaced. The warranty period on Boosters™ is three years free parts replacement.
Maximum continuous ambient temperature is 50 degrees C.
Boosters™ are designed to run induction motors most efficiently. Welders can also be operated but the convertor size should be chosen to be larger than the welder input power by 50%. If no power rating is shown then multiply the welding current by 50 for A series convertors or by 30 for D series convertors. The result will be the convertor power rating in Watts for 100 % duty factor, often misnamed duty cycle.
Radio frequency interference and electromagnetic interference are well below legal limits everywhere. Boosters™ are tested for EMC compliance and comply with applicable emission and radiation standards. Boosters™ comply with Wiring and Safety Regulations.
Boosters™ are robust and immune from incoming line disturbances, over- or undervoltage conditions and frequent short circuits. They resist the "dirty" supply from rural power lines. Brown-outs, black-outs, unstable power lines, over and under voltage will not harm a Booster™.
The standard input voltage is 220-240V single-phase and the standard output voltage is 380-415V 3phase. The output frequency is always as the input frequency: 47-63 Hz. Boosters™ are also available for other single phase, two phase or split phase input voltages such as 110-127V, 208V, 400V, 460V or 480V.
Customers in the UK, Europe and the Middle East should contact our business partner Ampair Energy Ltd
Tel: +44 (0)1258 837 266 Fax: +44 (0)1258 837 496
For customers in Asia, New Zealand, Pacific Islands, etc. we suggest you approach our business partner Eurotech Ltd
Tel: +64-7-8237 234 Fax: +64-7-8237 346
For customers in Australia, we suggest you approach our business partner Peter Martin Sales PTY LTD
Tel: (07)-1879 7844
For customers in the USA or Canada, we suggest you approach our business partner Martin's Electrical Services
Tel: (570) 668-4540
For customers in Mexico, we suggest you approach our business partner Blantek SA DE CV
Tel: 0112 01-1491
This site is a member of the Electrical Transformers WebRing.
[ Previous 5 Sites | Previous | Next | Next 5 Sites | Random Site | List Sites ]
For more details and/or to join this ring Go to Electrical Transformer WebRing home page
Links to rest of Isomatic UK site:
For explanation of 3 phase supplies and guide to converter selection, go to the 3 phase converter selection page
3 phase convertor page (mis-spelling of converter)
Go to rotary phase converter page (alternative names, otherwise identical)
Go to electrical transformer page
Go to coil winding page
Go to C cores page
Go to toroidal cores page
Go to resistance welding transformer page
Go to Isomatic table of contents (if no frames are showing or required)
Return to Isomatic home page (with frames and table of contents)
NOTE: Internet Explorer requires me to then click the Home Page link at the top of the contents list in the left-hand Isomatic UK frame. Firefox, Mozilla and Safari don't require this extra step.
Please send requests for quotations or any comments, criticisms, suggestions or questions concerning either this page or the Electrical Transformers WebRing to
This page was updated and its HTML syntax checked on 15 March 2011 using BBEdit on a MacBook Pro .
Isomatic has a policy of continual product improvement and therefore reserves the right to change specifications, dimensions and appearance from that shown on this web page.
This Isomatic web site names other companies and contains links to other sites. These names and links are not endorsements of any products or services from such companies or sites and no information in other sites has been endorsed or approved by this site.
These pages are hosted by West Dorset Internet (Wessex broadband) www.wdi.co.uk
Statistics on accesses to this page are provided by HitBox.